somethin' new - 08/28/06 09:02 PM
http://img247.imageshack.us/my.php?image=69fb038lk5.jpg 250 cu. in. ford
Re: somethin' new - 08/28/06 09:53 PM
Looks GOOD. What are those Injectors off? Custom manifolds, nice. Did you build the air intake fitted to the end of the injectors too.
Larry
Larry
Re: somethin' new - 08/28/06 11:15 PM
Re: somethin' new - 08/28/06 11:50 PM
I take it those injectors are off the shelf webers and very $$$$$$. Who is FSP?
Still looks good even for a F*rd.
Larry
Still looks good even for a F*rd.
Larry
Re: somethin' new - 08/29/06 12:02 AM
It is a good idea to run idividual throttle bodies for better driveability.
It looks sweet!!!!!!
Very expensive.$$$$$$$$$$$$$$$$$$$$$$$
You will not make anymore power than w/a common pleneum w/a single throttle body w/a turbocharger.
Plus having all those throttle bodies, it is more likely to have some leaks.
It looks sweet!!!!!!
Very expensive.$$$$$$$$$$$$$$$$$$$$$$$
You will not make anymore power than w/a common pleneum w/a single throttle body w/a turbocharger.
Plus having all those throttle bodies, it is more likely to have some leaks.
Re: somethin' new - 08/29/06 01:27 AM
The throttlebodies are from TWM,intake is a Aus 2v intake.The head is a prototype of a new aluminum head for the ford small six.The turbo manifold and DUI distributor are also FSP items aswell as the valvecover.The "baby brother" to this motor, if you will, with a latemodel log head 274 duration cam and stock internals with the turbo made 285 hp at around 4,500rpm and 450 ft.lbs. of torgue @ 3,500.The Twm setup runs around $1,800.
Re: somethin' new - 08/29/06 02:45 AM
82F-100,,,,,,,
Could you tell us some more about your cylinder head?
What size valves,how much the cylinder head flows?
How much does it cost?
Your set-up looks really nice. Does it run yet?
Have you dynoed it yet?
What EFI unit are you using?
Turbo specs?
Camshaft specs?
Did you see that(I think it was a Fairlane) Ford Fairlane in Hot rod magazine?
It had 6 cly, a stock cyl head ,turbo, carb, used intercooler & so-on ,ran 11's???
Your's put's that to shame!!
I see you do not have that much room to make a big plenum. Is that a piece of round aluminum tubing your using for a plenum?
Ok, I'll calm down now, it's just cool to see something simular that I will be doing in the future!!!
Could you tell us some more about your cylinder head?
What size valves,how much the cylinder head flows?
How much does it cost?
Your set-up looks really nice. Does it run yet?
Have you dynoed it yet?
What EFI unit are you using?
Turbo specs?
Camshaft specs?
Did you see that(I think it was a Fairlane) Ford Fairlane in Hot rod magazine?
It had 6 cly, a stock cyl head ,turbo, carb, used intercooler & so-on ,ran 11's???
Your's put's that to shame!!
I see you do not have that much room to make a big plenum. Is that a piece of round aluminum tubing your using for a plenum?
Ok, I'll calm down now, it's just cool to see something simular that I will be doing in the future!!!
Re: somethin' new - 08/30/06 02:47 AM
Hank, They just got the motor and tranny in this past weekend but haven't fired it up yet.The owners of the 63 falcon put the motor together and did all the fabrication for the intercooler inlet and outlet.A FAST system controls the engine.Your best bet is to check this out for info.http://fordsix.com/forum/viewtopic.php?t=35544
Re: somethin' new - 08/30/06 09:33 AM
that is one cool looking six. lots of time spent there. way above my goals.i have a hard enough time just putting the parts together. tom