I have a 250 kew motor , & wish to put triple carbs on it.
I have seen many with triple SU's , or triple stromberg/carters , but am thinking triple Webers. As these are cheap & currently made . Any opinions from people on this
also are the downdraft Strombergs any good ? Or really too crude compared to Webers?
Webers are going to be getting close to fuel injection as you can get.
They are great carbs, a lot of tuning required to get it right.
Meaning, if you do not get carbs set up for your inline, best to have a friend that has different emulsion tubes, & assortment of jets to be able to get things going in the right direction.
Or talk with someone that know what emulsion tube s you need & jetting.
It's been so long I cannot remember what I had in mine, but I used 3 48 MM Webers which are too big for a 250 on the street.
Webers are cheap? How much is cheap? Typical price $375 & up
http://www.ebay.com/itm/3-Genuine-WEBER-...ea7&vxp=mtrHere :
http://www.ebay.com/itm/Genuine-WEBER-45...958&vxp=mtr These are nice, but a bit big
http://www.ebay.com/itm/Weber-50mm-DCOE-...71d&vxp=mtrDecent price?
http://www.ebay.com/itm/JAGUAR-XKE-4-2-T...154&vxp=mtrMBHD
Thanks, cheap is a relative word, I can buy a new weber for $289.00 $aus.
I can buy second hand ones for a lot less, but if I did they would require work to undo years of people fiddling & possibly a rebuild . the bargain used ,becomes not such a bargain.
New Stromberg downdrafts are advertised here in Australia as $600 each!
Reconditioned often for the price of the webers. & I believe Webers would be better than Strombergs. Used Strombergs are common but all at best would need stripping to match jets etc, & all ,by now ,for decent performance would need the butterfly shafts rebushed adding more cost.
Not sure about all Weber DCOE's but mine (made in Italy) were ball bearing shafts & were sealed, great for blow through apps.
I would go with the Webers if you can.
I would get a book on Webers & do some research for the ones that would work best for you.
The more transitioning holes, (holes in the bores close to the throttle valves) the more the better, smoother, better drivability.
IIRC, my 48 MM carbs were made for a spec class of racing & only had 3 transitioning holes in the bores, had more of a on throttle off throttle feel, not so smooth, but I got used to it.
MBHD
Thanks, everyone seems to think webers when tuned have the smoothest power delivery. Though some people seem to think SU's are easier to work with.
I have come to conclusion people like what they know. I am still looking as there is plenty of carbs to choose from . & at times think simple carbs Stromberg or carter for simple people like me. As my Mopar is a hobby not a daily driver I think I like the idea of getting the best out of a carb. Any suggestions on intake runner length? I am trying to get power at 2500-3500 revs, this is where I mostly drive.
There is an adjustable jet available for the single-choke Stromberg used on the 202 motors in HQ Holdens. This makes them a nicely adjustable and very simple - as well as cheap - carby.
If you were talking about Weber DCOEs, how did you plan to use them? Use one choke of each?
The Webers I wish to use are single throat. downdraft carbs. Just a more refined Stromberg.
They are not from any car ,but a replacement for downdraft carbs.
Sounds like by the time you buy the webbers you're most of the way towards the cost to buy a new EFI system...
This has crossed my mind, Thing is I can understand carb's ,But would not know where to start with EFI. Cost is also relevant, this is a looooong project so any cost
will be regained with years of tinkering pleasure.
There is no logic to doing up this engine, it would be more practical to go down to my wrecker & buy a current OHC inline, I just want to do it.
What part of bananaland are you in?
What vehicle houses this engine?