Topic Options
Rate This Topic
#22799 - 01/19/04 10:15 PM Barker High Lift Intake Rocker Arms
Drew, II # 4211 Offline
Active BB Member
****

Registered: 08/10/03
Posts: 1905
Loc: Glassboro,NJ,USA
These are listed currently on Ebay and were apparently manufactured for Stelling and Hellings. Anybody have some history about
these? Did they actually help performance?
How did they work?



------------------
Drew
'55 Chevy
_________________________
Drew
Mid-Atlantic Chapter

Top
#22800 - 01/20/04 12:35 PM Re: Barker High Lift Intake Rocker Arms
stock49 Offline

Active BB Member
****

Registered: 04/09/03
Posts: 999
Loc: Medina, Ohio USA
Hi Drew

From what I have heard, B&B (Barker) was a seperate company until bought out by Stelling & Hellings.

'California' Bill Fisher talks about these in his speed manual.

They increase the rocker ratio from 1.5 to 1.7 yielding an increase in lift of .065. They replace just the intake rockers and while they don't change the advertised duration of your cam . . . they do increase its intake duration at .050.

They were advertised to increase output by 5 horse power on a stock 216. California Bill used them on every one of his 216 dyno-test builds - no matter how wild the cam was to begin with.

I have a set on hand for my 216 build.

regards,
stock49
_________________________

Top
#22801 - 01/20/04 02:13 PM Re: Barker High Lift Intake Rocker Arms
gearhead Offline
Active BB Member

Registered: 07/12/00
Posts: 1613
Loc: madison, wi
They will cause the pushrods to be at an angle, and would probably need the pushrod holes in the head to be massaged for clearance. It was my understanding that they were 1.6 ratio, but I could be remembering wrong. It should say in the instructions.

[This message has been edited by gearhead (edited 01-20-2004).]
_________________________
I.I. #3174

Top
#22802 - 01/21/04 09:07 AM Re: Barker High Lift Intake Rocker Arms
jimfred Offline
Member

Registered: 10/18/00
Posts: 24
Loc: Atlanta, GA
I have these, as well as a similar set of Fenton high lifts.

I tried the Fentons, and like gearhead says, they cause the pushrods to bend against the head. I took them out since I wasn't ready to modify the head at that time.

Jim

Top
#22803 - 01/21/04 11:57 AM Re: Barker High Lift Intake Rocker Arms
Drew, II # 4211 Offline
Active BB Member
****

Registered: 08/10/03
Posts: 1905
Loc: Glassboro,NJ,USA
Thanks everyone for the history.This is new stuff to me but I'm rapidly learning a lot from you all. I see California Bill's book is mentioned often, so I think I'll buy one.

------------------
Drew
'55 Chevy
_________________________
Drew
Mid-Atlantic Chapter

Top
#22804 - 01/21/04 07:59 PM Re: Barker High Lift Intake Rocker Arms
cujo Offline
Member

Registered: 09/09/02
Posts: 40
Loc: Williamson, NY, USA
Is any one using these Hi-lift rockers on their engine? What kind of performance gains have you noticed with them? Besides the push rod / head clearance issue are there any other problems running these Hi-lift rockers?

Top
#22805 - 01/24/04 03:23 PM Re: Barker High Lift Intake Rocker Arms
stock49 Offline

Active BB Member
****

Registered: 04/09/03
Posts: 999
Loc: Medina, Ohio USA
Thanks for the heads up gearhead/jimfred . . . I will watch the pushrod hole clearances closely when I do my build. Perhaps I may even try fit & run them on the stock setup before I tear it down.

As for the instructions, they pretty much say "slap em in, set the lash and go"


barkerinstructions.jpg

Up until I read jimfred's reply on this thread I had never heard of clearance or bending problems with higher than stock ratio rockers. But I am new to wrenching on Sixes.

When I was younger we played with V8s and this was just another variable. In fact I have read several tech articles that suggest that a balance of increased rocker ratio and lobe lift is easier on the valve train than increasing only lobe lift: http://www.pontiacstreetperformance.com/psp/RockerArms.html

The other thing that I am curious about is just how tight are the pushrod holes in an inliner? Based on my measurements these rockers don't move the top of push rod very far at all.

The distance from the fulcrum to the valve stem is roughly 2.1". The stock rocker ratio is 1.5. So the distance from the fulcrum to push rod is roughly 1.4".

Well I measured the Barker's this morning:


rockerratio1.jpg

Of course Barker can't vary the distance to valve stem -- so it is roughly stock. But the distance to the push rod is indeed shorter as we would expect in order to acheive the higher ratio


rockerratio2.jpg

2.1" divided by a rocker ratio of 1.7 = 1.235". Which is a difference of .16" and with a rougly 11" push rod we are moving it about .88 degrees off perpendicular. Doesn't seem like enough to create a risk of bending the rod. Yet now that I think about it .16 is the better part of three pennies . . . perhaps I will need to do some grinding.

For those who have never seen these before, there are some more pics below . . .

stock49


barker1.jpg


barker2.jpg


barker2.jpg
_________________________

Top
#22806 - 02/14/04 10:39 AM Re: Barker High Lift Intake Rocker Arms
chuddy117 Offline
Member

Registered: 03/20/01
Posts: 23
Loc: Duluth, Minnesota
I actually have a set on Ebay right now. I dont know the rules of this forum so I won't post a link, but just do a search. I actually have 2 NOS sets of these and was going to put them on my 235, but found out they won't work. However, I do have a set of Thomas adjustable magnesium rocker arms for 235/261's. Has anyone ever heard of them? I hate to use them because Magnesium gets so brittle, but they're kinda neat and SUPER light!
Chad
_________________________
1955 Chevrolet 210 2 door Sedan
a 30,000 mile UNMOLESTED original, now my daily driver! Original 6 cylinder with a rebuilt '66-'69 Saginaw 3-speed Overdrive. Synchro low! Otherwise, everything original down to the spare tire. Interior is like new. Needs paint, but absolutely zero rust.

Top
#22807 - 02/14/04 08:16 PM Re: Barker High Lift Intake Rocker Arms
chevyman1937 Offline
Member

Registered: 10/18/02
Posts: 125
Loc: Rockford, Illinois
Why won't these work on your 235? I just tore down a 58 to 62 261 and discovered the rocker arm shafts are trash so i imagine the rockers are also. Will these work on my 261?
_________________________
Gael
37 chevy sedan, 261,t5
57 pickup
58 burb

Top
#22808 - 02/14/04 10:44 PM Re: Barker High Lift Intake Rocker Arms
chuddy117 Offline
Member

Registered: 03/20/01
Posts: 23
Loc: Duluth, Minnesota
I have heard from several people that 216 rocker arms WILL NOT work with 235/261 engines. Something about the angle is different?
_________________________
1955 Chevrolet 210 2 door Sedan
a 30,000 mile UNMOLESTED original, now my daily driver! Original 6 cylinder with a rebuilt '66-'69 Saginaw 3-speed Overdrive. Synchro low! Otherwise, everything original down to the spare tire. Interior is like new. Needs paint, but absolutely zero rust.

Top
#22809 - 02/15/04 08:58 PM Re: Barker High Lift Intake Rocker Arms
gearhead Offline
Active BB Member

Registered: 07/12/00
Posts: 1613
Loc: madison, wi
if you have a 58-62 block, you should use 58-62 rocker arms, or the amount of oil going to the top end may be affected. The oil groove size in the arms was changed when they went from the oil line system ('57-earlier) to the drilled block system 58-62.
_________________________
I.I. #3174

Top
#22810 - 02/16/04 10:21 AM Re: Barker High Lift Intake Rocker Arms
thetrueslayer Offline
Member

Registered: 02/12/04
Posts: 242
Loc: chilliwack, BC in Canada
or for bout 500.00 u could get some roller rockers which last forever and supposedly increase performance cause of the less friction/less work the engine has to do.
_________________________
got my 78 merc with a 250 I6 and i love it.

Top
#22811 - 03/01/04 04:41 AM Re: Barker High Lift Intake Rocker Arms
cujo Offline
Member

Registered: 09/09/02
Posts: 40
Loc: Williamson, NY, USA
I was not aware someone made roller rockers for the 235/261. Who sells them?

Top
#22812 - 11/02/06 12:40 AM Re: Barker High Lift Intake Rocker Arms
bareknuckle Offline
Junior Member

Registered: 08/15/06
Posts: 1
Loc: new london,ct.
hey, i am a custom bike builder, who just picked up a 64 impala, 230 I6. now i use corrected ratio rocker arms on my bikes all the time. because i will find a nice steep ramp slope, and suitable duration to put me in the torque band i am looking for, but if i want to step up in cam size, all that goes away... a higher duration usualy means wider more gradual ramps, killing my bottom end...so with the 1.7 rockers i get the bennifet of the steep ramps ultimatly narrower durration, but the benafit of the higher lift.....which will slightly affect durration, but rarely noticeable...so now calculate the real difference between your mechanical, and your corrected compression ratio, by measuring dome, squish, and compressed gasket height, as well as knowing your valve overlap...so as u can see i am all for high lift rockers..however on the bikes, to keep from any power loss due to heat and friction,as well as push rod flexing. i use taperlites..which reduce in outer diameter, from 7/16. to 3/8 .so all stress nstays within the rod itself. its not a uniform shape that can bend or disfigure... so does anyone know if they make anything like taperlites for auto use...just a suggestion...let me know............bareknuckle...

Top
#22813 - 11/02/06 02:58 AM Re: Barker High Lift Intake Rocker Arms
John H. Meredith Offline
Active BB Member
*****

Registered: 12/10/00
Posts: 3332
Loc: Apple Valley, California, USA
Gentlemen;

These were on e-bay a few weeks back (Barker) & a lot of money as I recall.

These worked good back in the 50s & many used them cause it was easy to put them on, instead of changing the cam. The push rods would rub a little as Bryan mentioned but not 'bend' and they weren't "roller" rockers, just 'hi lift'.

There okay for stock but N/G with a 'cam' as the lift is to much & can cause the valve spring to collapse completly.

They were part of the "Hot Rod package" many did.
Milled head (.125), high lift rockers, 2 carb & headers with a hot coil too.

It would make a 85Hp 216" engine 140+/- and made money for the Accessory Houses \:\) plus a lot of noise. \:D
_________________________
John M., I.I. #3370

"There are no shortcuts to any place worth going". -Anon

Top
#64871 - 05/21/11 09:55 AM Re: Barker High Lift Intake Rocker Arms [Re: John H. Meredith]
popper6 Offline
Active BB Member
*****

Registered: 12/15/04
Posts: 226
Loc: La Harpe,IL.
On the Buick str 8 I screwed a bolt in to the adjustment hole on the rocker arm- milled it flat-made a fixture with a guide hole in it and redrilled the adjustment screw hole closer to the rocker shaft. I did have a clearance problem with the push rod-cured by using the same die grinder I ported the head with I ground the clearance I needeed . The problem was at the top of the hole 1'-1.5' down. Buicks had tubular pushrods and I never bend any at 6000 RPM. Is there anybody else out there that would like to build an engine the way we used to without all the technoligy we have today- just to see if it still works??? 1 OL REDNECK.
_________________________
DARRELL KRAFT I.I.#113

Top
#64873 - 05/21/11 11:14 AM Re: Barker High Lift Intake Rocker Arms [Re: popper6]
panic Offline
Active BB Member
**

Registered: 01/11/05
Posts: 1496
Loc: Hempstead, Long Island, NY
That works on anything with enough area between the adjuster hole and the center shaft tunnel area.
Sometimes you get either more ratio, or more safety margin (or both) by reducing the adjuster thread size, but match the ball diameter to your original or you'll need new pushrods.
The new ratio has to be a substantial change to justify the work (not to mention using up the rockers!).
Example only: the distance from the shaft center to the pushrod adjuster ball center is 1-11/32" (1.34375"). and that from the shaft to the pad radius center is 2", the ratio is 2 1.34375, or 1.488:1. Lift with a .280" lobe is .417"
Moving the adjuster 1/8" closer makes the ratio 2 1.28125, or 1.64:1. This adds about .042" to the lift.

Top
#64955 - 05/26/11 11:55 AM Re: Barker High Lift Intake Rocker Arms [Re: chuddy117]
jimmy six #35 Offline
Active BB Member
*****

Registered: 08/31/06
Posts: 289
Loc: So Cal
I have 2 sets of NOS Thomas Magnesium rockers for a GMC but have never used them on any of my race engines. They were for both intake and exhaust. The stock adjusters were supposed to be used with them. I was always leary of using them because of the surfaces on the shaft. The push rod hole becomes a problem when you go to larger diameter push rods. I believe the problem would start with the 3/8" ones, 5/16" might make it.
_________________________
216.158 MPH 12-Port 302 GMC on 70% 171.0 MPH 302 stock head on gasoline 7 years later

Top
#65001 - 05/29/11 02:37 PM Re: Barker High Lift Intake Rocker Arms [Re: jimmy six #35]
telekenfun Offline
Bulletin Board Only Member

Registered: 08/26/07
Posts: 4
Loc: Anchorage. Alaska
I'm building up a Buick straight eight presently. After careful measurement the best ratio possible from the stock rocker is 1.51:1 when the adjuster ball is screwed nearly all the way up into the rocker. This is unuseable as the oiler holes no longer line up in this rather tenuous oiling setup to begin with. With the adjuster lowered to a more practical place in the rocker the ratio drops to 1.42:1.
My solution was to physically relocate the rocker arm shaft .062 closer to the pushrods. I offset bored and rebushed the rocker arms and shaft stantions .062 towards the pushrod side of the engine.The net result is I now have a 1.66:1 rocker ratio, and no interference at the pushrod holes in the head.
It cost me a week of spare time making the jigs to bore the rockers and stantions another week to do the machine work and about $80 worth of bushings and high temp bushing lock.

Top

Moderator:  nln6pinto, will6er 
Who's Online
1 registered (41 Coupe), 42 Guests and 3 Spiders online.
Key: Admin, Global Mod, Mod
Newest Members
Danrush, Billy ray, J Mann, John Forbes, 59GMC
6025 Registered Users