Page 1 of 1 1
Topic Options
Rate This Topic
#68887 - 03/04/12 10:08 PM billet bulkhead connector
efi-diy Offline
Active BB Member
*****

Registered: 11/21/04
Posts: 1451
Loc: Calgary Alberta Canada
[url=]30 pin firewall pass through[/url]

[url=]front view[/url]

Ever wanted to have a clean method to get wiring though a bulkhead (firewall).. and be able to disconnect the harness..

This is a 30 pin connector with 6 places for 10ga wires the rest are good for smaller loads or sensors.

The connector is watertight once the wire are inserted with the seal. The actual connector is made by Delphi - the billet block made here.


Edited by efi-diy (03/04/12 10:12 PM)
_________________________
51 GMC 4.2 turbo
Can't solved today's problems using the same technology/thinking that created them

Top
#68889 - 03/05/12 11:30 AM Re: billet bulkhead connector [Re: efi-diy]
Beater of the Pack Offline
Active BB Member
****

Registered: 10/06/07
Posts: 2891
Loc: Northern Nevada
Damn, I may have to revise my NO BILLIT rule! \:D That is neat.
_________________________
"I wonder if God created man because he was disappointed in the monkey?" Mark Twain

Top
#68912 - 03/06/12 05:47 PM Re: billet bulkhead connector [Re: Beater of the Pack]
efi-diy Offline
Active BB Member
*****

Registered: 11/21/04
Posts: 1451
Loc: Calgary Alberta Canada
If anyone is interested I could supply either just the block or a kit ready to go.
_________________________
51 GMC 4.2 turbo
Can't solved today's problems using the same technology/thinking that created them

Top
#68919 - 03/07/12 06:54 AM Re: billet bulkhead connector [Re: efi-diy]
Titen Administrator Offline
Active BB Member
****

Registered: 10/22/00
Posts: 360
Loc: Weimar, California 95736
Nice piece, however, this should be in the 'Swap Meet' forum.

Tim
_________________________
Tim Tenold
I.I.#498

Top
#68930 - 03/07/12 09:48 PM Re: billet bulkhead connector [Re: Beater of the Pack]
efi-diy Offline
Active BB Member
*****

Registered: 11/21/04
Posts: 1451
Loc: Calgary Alberta Canada
 Originally Posted By: Beater of the Pack
Damn, I may have to revise my NO BILLIT rule! \:D That is neat.


... camo it - flat black.....
_________________________
51 GMC 4.2 turbo
Can't solved today's problems using the same technology/thinking that created them

Top
#68931 - 03/07/12 11:59 PM Re: billet bulkhead connector [Re: efi-diy]
Nexxussian Offline
Active BB Member
*****

Registered: 06/12/07
Posts: 1411
Loc: Anchorage
What pins does it use (wether pack, wedge lock, ....)?
_________________________
My, what a steep learning curve. Erik II#5155

Top
#68932 - 03/08/12 11:17 AM Re: billet bulkhead connector [Re: Nexxussian]
efi-diy Offline
Active BB Member
*****

Registered: 11/21/04
Posts: 1451
Loc: Calgary Alberta Canada
delphi metric-pak 240&480
_________________________
51 GMC 4.2 turbo
Can't solved today's problems using the same technology/thinking that created them

Top
#68939 - 03/08/12 09:37 PM Re: billet bulkhead connector [Re: efi-diy]
Nexxussian Offline
Active BB Member
*****

Registered: 06/12/07
Posts: 1411
Loc: Anchorage
Thank you.
_________________________
My, what a steep learning curve. Erik II#5155

Top
Page 1 of 1 1


Moderator:  Webmaster 
Hop to:
Who's Online
3 registered (Drew, II # 4211, tlowe #1716, littlejeep2) and 59 anonymous users online.
Newest Members
Crow, drgoetz, ulfy5082, richard owens, adamohlmeier
5681 Registered Users

Generated in 0.07 seconds in which 0.029 seconds were spent on a total of 14 queries. Zlib compression unavailable.