Topic Options
Rate This Topic
#71113 - 08/13/12 05:44 PM Chevy 230 remove crank without pulling the engine?
70Nova Offline
Active BB Member
****

Registered: 05/06/11
Posts: 374
Loc: Va
Bear with me, it's probably a stupid question but I'm tired and I just happened to look at things underneath today as I pulled the oil pan and rods&pistons out.... and I thought, "Hmm, what's stopping the crank from coming out if i unbolt the torque converter and the bearing caps?" Is it possible?

I have to get it out and have the rod bearing journals machined.

I have no trouble pulling the engine, I was just wondering.... why would I if its not needed?


Jan

Top
#71120 - 08/13/12 11:31 PM Re: Chevy 230 remove crank without pulling the engine? [Re: 70Nova]
CNC-Dude #5585 Offline
Active BB Member
****

Registered: 09/27/08
Posts: 3272
Loc: N. Georgia
It can be done, you'll likely wish you had gotten a root canal instead though. \:D I definately wouldn't want to trade that chore with anyone.
_________________________

Inliners International Advertiser

Top
#71124 - 08/14/12 11:07 AM Re: Chevy 230 remove crank without pulling the engine? [Re: CNC-Dude #5585]
Harry 6674 II 5760 Offline
Active BB Member
***

Registered: 05/03/10
Posts: 134
Loc: Washington
If your crank needs to be machined your oil passages should probably be flushed and cam bearings be replaced?

Top
#71125 - 08/14/12 05:19 PM Re: Chevy 230 remove crank without pulling the engine? [Re: Harry 6674 II 5760]
70Nova Offline
Active BB Member
****

Registered: 05/06/11
Posts: 374
Loc: Va
Good point, I had not thought about the cam bearings.

I just wanted to refresh this thing and make it work right and serve as my backup if and when I get a 292 done... I'm torn, don't really want to dump more money in this engine. My plans "live" a little as time goes by, and now I have a friend's dad procrastinating with his 292-SBC swap. That engine is earmarked for me... he just needs to pull it out.

Jan

Top
#71129 - 08/14/12 07:01 PM Re: Chevy 230 remove crank without pulling the engine? [Re: CNC-Dude #5585]
stock49 Offline

Active BB Member
****

Registered: 04/09/03
Posts: 999
Loc: Medina, Ohio USA
 Originally Posted By: CNC-Dude #5585
It can be done, you'll likely wish you had gotten a root canal instead though. \:D


An engine stand allows for the block to be inverted for this step. I can't imagine how you would support the crank while removing the mains - and then the reverse to install with fresh bearings - not to mention with the patience to plasti-gauge the clearances while on your back . . . which is typically at least two installations/torque ups with tear downs to read tolerances. By the third install you would probably be quite skilled at doing this on your back . . .

regards,
stock49

Top
#71131 - 08/14/12 09:39 PM Re: Chevy 230 remove crank without pulling the engine? [Re: stock49]
bcowanwheels Offline
Active BB Member
*

Registered: 10/04/07
Posts: 411
Loc: kingsport, tn.
I,VE REPLACED THE CRANKS IN ENGINES STILL IN CARS AND SEMIS ALOT IN THE PAST WITH PISTONS STILL IN THE BLOCK ! NO BIG DEAL ESPECIALLY IF YOU HAVE A HELPER.
_________________________
I BELIEVE IN " JOHN 3:16 "

Top
#71132 - 08/14/12 11:27 PM Re: Chevy 230 remove crank without pulling the engine? [Re: bcowanwheels]
CNC-Dude #5585 Offline
Active BB Member
****

Registered: 09/27/08
Posts: 3272
Loc: N. Georgia
As stock49 mentioned, you cant plastigage the mains unless its on an engine stand inverted. Its just going to be a crap shoot as to the bearing clearances if that was in the plans to do.
_________________________

Inliners International Advertiser

Top
#71140 - 08/15/12 04:56 PM Re: Chevy 230 remove crank without pulling the engine? [Re: CNC-Dude #5585]
Mean buzzen half dozen A.K.A. Hank Offline
Active BB Member
***

Registered: 09/23/04
Posts: 5813
Loc: Ca
You guys do not need to use plastigage. You can use T-gauges dial bore indicators, outside mics etc to get your measurements.

You guys already know this.

If you shop around you can get new tools cheap (china) but you can also buy used tools of better quality.

MBHD
_________________________
12 port SDS EFI

Top
#71141 - 08/15/12 05:34 PM Re: Chevy 230 remove crank without pulling the engine? [Re: Mean buzzen half dozen A.K.A. Hank]
stock49 Offline

Active BB Member
****

Registered: 04/09/03
Posts: 999
Loc: Medina, Ohio USA
 Originally Posted By: Mean buzzen half dozen A.K.A. Hank
You can use T-gauges dial bore indicators, outside mics etc to get your measurements.


I am a fan of all of the above. The mics and gauges tell one story while the plastigage tells what's going on when it is all bolted together.

For me it's the last gut check prior to final assembly.

Top
#71143 - 08/15/12 07:30 PM Re: Chevy 230 remove crank without pulling the engine? [Re: stock49]
Mean buzzen half dozen A.K.A. Hank Offline
Active BB Member
***

Registered: 09/23/04
Posts: 5813
Loc: Ca
Just some FYI.

If you do not store the plastigage in the fridge, it will cause for inaccurate readings, or if being left out in the heat too long.

MBHD
_________________________
12 port SDS EFI

Top
#71163 - 08/16/12 09:03 PM Re: Chevy 230 remove crank without pulling the engine? [Re: Mean buzzen half dozen A.K.A. Hank]
70Nova Offline
Active BB Member
****

Registered: 05/06/11
Posts: 374
Loc: Va
Done all that before, more than once, plastigage included, under the car. Replaced main bearings too. No I do not love punishing myself like that \:\)

At this point I am not concerned about measuring anything since I will have the damn thing machined to an exact size. I'll measure when it comes back from the machine shop, just to make sure they didn't screw up.

I may end up pulling the engine and putting it on a stand, that was my plan anyways. I just wanted to know if the crank had room to come out without separating the engine from the trans. I guess it's a matter of how deep it engages with the torque converter and how far back the TC can be pushed once unbolted.
I can see a challenge in supporting the crank evenly when removing the caps, as well as putting it back in \:D
Don't need a banana for a crank.
I was just curious.

Top
#71169 - 08/17/12 10:03 AM Re: Chevy 230 remove crank without pulling the engine? [Re: 70Nova]
strokersix Offline
Active BB Member
*****

Registered: 05/23/09
Posts: 426
Loc: NW Illinois, USA
Modify your radiator support to make a removable section in the middle makes it a lot easier to pull engine and trans as a unit. Be sure you have a 1.5 inch OD tube or driveshaft yoke to plug the back end of your trans or you will make a mess for sure.

Top
#71186 - 08/17/12 08:41 PM Re: Chevy 230 remove crank without pulling the engine? [Re: strokersix]
70Nova Offline
Active BB Member
****

Registered: 05/06/11
Posts: 374
Loc: Va
Just bent over backwards with the damn radiator.. new rad, 3 row instead of the old 2 row, and electric fan conversion.. hate taking it all out again, lol.

I was hoping to be able to yank just the engine out. Haven't done that yet on this car. Due to some unfortunate circumstances (stupidity, short sightedness, etc.) I can't use the concrete floor 2 feet away from the car, I have to do it on dirt. The engine hoist does not roll on dirt... not an inch. I can maneuver a stripped down engine block around but having to deal with the trans glued to it will be a pain. I have no reason to pull the trans out, but knowing myself, if I do take it out the project will once again escalate beyond my original scope... \:D I would rather not face the temptation.

Jan

Top

Moderator:  nln6pinto, will6er 
Who's Online
0 registered (), 23 Guests and 4 Spiders online.
Key: Admin, Global Mod, Mod
Newest Members
Tuscagi2, Danrush, Billy ray, J Mann, John Forbes
6026 Registered Users