261 block machining opinions needed

12 Port News - Features

12 Port History

Casting Numbers

Online Store

Tech Tips

Become a Member

Print Thread

Rate Thread

Re: 261 block machining opinions needed CNC-Dude #5585 #57238 04/28/10 09:26 PM
Joined: Mar 2001 Posts: 64 San Francisco, CA USA M mark50 OP Active BB Member
OP mark50 Active BB Member M Joined: Mar 2001 Posts: 64 San Francisco, CA USA	The cam is solid lift and suggested lash is .012". I had zero lash at TDC on #1 cylinder. Hopefully I did this correctly! If so I can then add the .012" to my total and be safe with decking the block at .030"?

Entire Thread
Subject	Posted By	Posted
261 block machining opinions needed	mark50	04/12/10 12:05 AM
Re: 261 block machining opinions needed	Ron Golden	04/12/10 12:21 AM
Re: 261 block machining opinions needed	CNC-Dude #5585	04/12/10 12:32 AM
Re: 261 block machining opinions needed	mark50	04/12/10 02:55 AM
Re: 261 block machining opinions needed	panic	04/12/10 09:53 AM
Re: 261 block machining opinions needed	mark50	04/12/10 03:59 PM
Re: 261 block machining opinions needed	Ron Golden	04/12/10 08:45 PM
Re: 261 block machining opinions needed	mark50	04/21/10 04:46 PM
Re: 261 block machining opinions needed	panic	04/21/10 07:13 PM
Re: 261 block machining opinions needed	mark50	04/21/10 07:26 PM
Re: 261 block machining opinions needed	CNC-Dude #5585	04/21/10 07:34 PM
Re: 261 block machining opinions needed	mark50	04/21/10 07:46 PM
Re: 261 block machining opinions needed	CNC-Dude #5585	04/21/10 08:12 PM
Re: 261 block machining opinions needed	mark50	04/21/10 08:36 PM
Re: 261 block machining opinions needed	CNC-Dude #5585	04/21/10 08:53 PM
Re: 261 block machining opinions needed	mark50	04/21/10 09:22 PM
Re: 261 block machining opinions needed	CNC-Dude #5585	04/21/10 09:48 PM
Re: 261 block machining opinions needed	panic	04/22/10 12:53 AM
Re: 261 block machining opinions needed	mark50	04/22/10 09:47 PM
Re: 261 block machining opinions needed	CNC-Dude #5585	04/22/10 10:26 PM
Re: 261 block machining opinions needed	panic	04/23/10 12:00 AM
Re: 261 block machining opinions needed	g.m. dude	04/23/10 04:36 AM
Re: 261 block machining opinions needed	mark50	04/28/10 03:56 PM
Re: 261 block machining opinions needed	CNC-Dude #5585	04/28/10 07:08 PM
Re: 261 block machining opinions needed	mark50	04/28/10 09:26 PM
Re: 261 block machining opinions needed	panic	04/29/10 09:15 AM
Re: 261 block machining opinions needed	mark50	04/29/10 01:49 PM
Re: 261 block machining opinions needed	panic	04/29/10 05:22 PM

Moderated by stock49, Twisted6, will6er

Link Copied to Clipboard

Inliners International Forums General Discussion Engines 261 block machining opinions needed