250 block what head should I use?

12 Port News - Features

12 Port History

Casting Numbers

Online Store

Tech Tips

Become a Member

Print Thread

Rate Thread

Re: 250 block what head should I use? bcowanwheels #69578 04/29/12 08:47 PM
Joined: Apr 2012 Posts: 17 Orange, MA W wekyle2012 OP Active BB Member
OP wekyle2012 Active BB Member W Joined: Apr 2012 Posts: 17 Orange, MA	That is something that I have in mind for the future but the engine has reasonably low miles and I am going to run it until something goes before I pull the bottom end apart. I love the look of the I6 in my truck so I will never swap to a V8, plus people are always surprised its not a 350, I guess everyone just expects that what you have under the hood.

Entire Thread
Subject	Posted By	Posted
250 block what head should I use?	wekyle2012	04/29/12 03:16 PM
Re: 250 block what head should I use?	Mean buzzen half dozen A.K.A. Hank	04/29/12 05:15 PM
Re: 250 block what head should I use?	wekyle2012	04/29/12 05:58 PM
Re: 250 block what head should I use?	CNC-Dude #5585	04/29/12 06:36 PM
Re: 250 block what head should I use?	wekyle2012	04/29/12 07:02 PM
Re: 250 block what head should I use?	wekyle2012	04/29/12 07:05 PM
Re: 250 block what head should I use?	Mean buzzen half dozen A.K.A. Hank	04/29/12 07:17 PM
Re: 250 block what head should I use?	wekyle2012	04/29/12 08:10 PM
Re: 250 block what head should I use?	bcowanwheels	04/29/12 08:40 PM
Re: 250 block what head should I use?	wekyle2012	04/29/12 08:47 PM
Re: 250 block what head should I use?	bcowanwheels	04/30/12 02:48 AM
Re: 250 block what head should I use?	wekyle2012	04/30/12 08:06 AM
Re: 250 block what head should I use?	bcowanwheels	04/30/12 05:38 PM
Re: 250 block what head should I use?	wekyle2012	04/30/12 06:07 PM
Re: 250 block what head should I use?	bcowanwheels	04/30/12 11:36 PM
Re: 250 block what head should I use?	tlowe #1716	04/30/12 11:39 PM
Re: 250 block what head should I use?	wekyle2012	05/01/12 11:08 AM
Re: 250 block what head should I use?	CNC-Dude #5585	05/01/12 01:04 PM
Re: 250 block what head should I use?	wekyle2012	05/01/12 01:27 PM
Re: 250 block what head should I use?	bcowanwheels	05/01/12 08:01 PM
Re: 250 block what head should I use?	wekyle2012	05/01/12 08:49 PM
Re: 250 block what head should I use?	Mean buzzen half dozen A.K.A. Hank	05/01/12 10:08 PM
Re: 250 block what head should I use?	bcowanwheels	05/01/12 11:59 PM
Re: 250 block what head should I use?	wekyle2012	05/02/12 09:50 AM
Re: 250 block what head should I use?	CNC-Dude #5585	05/02/12 01:26 PM
Re: 250 block what head should I use?	wekyle2012	05/02/12 05:50 PM
Re: 250 block what head should I use?	Mean buzzen half dozen A.K.A. Hank	05/02/12 09:41 PM
Re: 250 block what head should I use?	wekyle2012	05/02/12 09:56 PM
Re: 250 block what head should I use?	tlowe #1716	05/02/12 11:19 PM
Re: 250 block what head should I use?	wekyle2012	05/03/12 01:33 AM
Re: 250 block what head should I use?	Twisted6	05/03/12 06:25 PM
Re: 250 block what head should I use?	wekyle2012	05/03/12 07:02 PM
Re: 250 block what head should I use?	Mean buzzen half dozen A.K.A. Hank	05/03/12 09:41 PM
Re: 250 block what head should I use?	wekyle2012	05/03/12 10:32 PM

Moderated by stock49, Twisted6, will6er

Link Copied to Clipboard

Inliners International Forums General Discussion Engines 250 block what head should I use?