250 block what head should I use?

12 Port News - Features

12 Port History

Casting Numbers

Online Store

Tech Tips

Become a Member

Print Thread

Rate Thread

Re: 250 block what head should I use? wekyle2012 #69599 05/01/12 10:08 PM
Joined: Sep 2004 Posts: 5,839 Likes: 1 Ca M Mean buzzen half dozen A.K.A. Hank 1000 Post Club
Mean buzzen half dozen A.K.A. Hank 1000 Post Club M Joined: Sep 2004 Posts: 5,839 Likes: 1 Ca	Glad you found a cyl head, but just remember, you are going to still have low compression. You could have the head milled some more to help raise the compression a bit. It's not that critical, but I thought you were wanting to bump up the performance. Goodluck on your build. MBHD MBHD 12 port SDS EFI

Entire Thread
Subject	Posted By	Posted
250 block what head should I use?	wekyle2012	04/29/12 03:16 PM
Re: 250 block what head should I use?	Mean buzzen half dozen A.K.A. Hank	04/29/12 05:15 PM
Re: 250 block what head should I use?	wekyle2012	04/29/12 05:58 PM
Re: 250 block what head should I use?	CNC-Dude #5585	04/29/12 06:36 PM
Re: 250 block what head should I use?	wekyle2012	04/29/12 07:02 PM
Re: 250 block what head should I use?	wekyle2012	04/29/12 07:05 PM
Re: 250 block what head should I use?	Mean buzzen half dozen A.K.A. Hank	04/29/12 07:17 PM
Re: 250 block what head should I use?	wekyle2012	04/29/12 08:10 PM
Re: 250 block what head should I use?	bcowanwheels	04/29/12 08:40 PM
Re: 250 block what head should I use?	wekyle2012	04/29/12 08:47 PM
Re: 250 block what head should I use?	bcowanwheels	04/30/12 02:48 AM
Re: 250 block what head should I use?	wekyle2012	04/30/12 08:06 AM
Re: 250 block what head should I use?	bcowanwheels	04/30/12 05:38 PM
Re: 250 block what head should I use?	wekyle2012	04/30/12 06:07 PM
Re: 250 block what head should I use?	bcowanwheels	04/30/12 11:36 PM
Re: 250 block what head should I use?	tlowe #1716	04/30/12 11:39 PM
Re: 250 block what head should I use?	wekyle2012	05/01/12 11:08 AM
Re: 250 block what head should I use?	CNC-Dude #5585	05/01/12 01:04 PM
Re: 250 block what head should I use?	wekyle2012	05/01/12 01:27 PM
Re: 250 block what head should I use?	bcowanwheels	05/01/12 08:01 PM
Re: 250 block what head should I use?	wekyle2012	05/01/12 08:49 PM
Re: 250 block what head should I use?	Mean buzzen half dozen A.K.A. Hank	05/01/12 10:08 PM
Re: 250 block what head should I use?	bcowanwheels	05/01/12 11:59 PM
Re: 250 block what head should I use?	wekyle2012	05/02/12 09:50 AM
Re: 250 block what head should I use?	CNC-Dude #5585	05/02/12 01:26 PM
Re: 250 block what head should I use?	wekyle2012	05/02/12 05:50 PM
Re: 250 block what head should I use?	Mean buzzen half dozen A.K.A. Hank	05/02/12 09:41 PM
Re: 250 block what head should I use?	wekyle2012	05/02/12 09:56 PM
Re: 250 block what head should I use?	tlowe #1716	05/02/12 11:19 PM
Re: 250 block what head should I use?	wekyle2012	05/03/12 01:33 AM
Re: 250 block what head should I use?	Twisted6	05/03/12 06:25 PM
Re: 250 block what head should I use?	wekyle2012	05/03/12 07:02 PM
Re: 250 block what head should I use?	Mean buzzen half dozen A.K.A. Hank	05/03/12 09:41 PM
Re: 250 block what head should I use?	wekyle2012	05/03/12 10:32 PM

Moderated by stock49, Twisted6, will6er

Link Copied to Clipboard

Inliners International Forums General Discussion Engines 250 block what head should I use?