|
|
Joined: Aug 2011
Posts: 11
Active BB Member
|
OP
Active BB Member
Joined: Aug 2011
Posts: 11 |
Does anyone know where I could buy the mounting brackets?
|
|
|
|
Joined: Aug 2003
Posts: 1,905
1000 Post Club
|
1000 Post Club
Joined: Aug 2003
Posts: 1,905 |
Drew Mid-Atlantic Chapter
|
|
|
|
Joined: May 2000
Posts: 1,464
1000 Post Club
|
1000 Post Club
Joined: May 2000
Posts: 1,464 |
I'll sell you this entire front end drive assembly - alternator, P/S, AC, etc. - less the damper for $150 firm.
Last edited by THE FRENCHTOWN FLYER; 01/21/13 03:31 PM.
FORD 300 inline six - THE BEST KEPT SECRET IN DRAG RACING!
|
|
|
|
Joined: Aug 2012
Posts: 166
Contributor
|
Contributor
Joined: Aug 2012
Posts: 166 |
If your going the non traditional route such as a street rod you can get the Davis Speed brackets like this.
|
|
|
|
Joined: Oct 2007
Posts: 411
Contributor
|
Contributor
Joined: Oct 2007
Posts: 411 |
ORIGINAL 250 P/S STUFF IS VERY EXPENSIVE AND VERY HARD TO FIND AND A/C STUFF IS EVEN HIGHER AND HARDER TO FIND... THEY DIDNT MAKE ALOT OF THIS AS THE 250 WAS ENTRY LEVEL ENGINES. AFTERMARKET OR MAKE YOUR OWN IS THE WAY TO GO. JMO
I BELIEVE IN " JOHN 3:16 "
|
|
|
|
Joined: Aug 2011
Posts: 11
Active BB Member
|
OP
Active BB Member
Joined: Aug 2011
Posts: 11 |
|
|
|
|
Joined: Aug 2011
Posts: 11
Active BB Member
|
OP
Active BB Member
Joined: Aug 2011
Posts: 11 |
I didn't think you could get AC for that.
|
|
|
|
Joined: Apr 2006
Posts: 831
Major Contributor
|
Major Contributor
Joined: Apr 2006
Posts: 831 |
'45 Ford PU 66 Valiant wagon, leaning tower of power. 79 Chevy C10 w/250 02 PT Cruiser Convertable
|
|
|
|
Joined: Aug 2011
Posts: 11
Active BB Member
|
OP
Active BB Member
Joined: Aug 2011
Posts: 11 |
I saw that, and if I can't find one that is close to original, I will buy his.
|
|
|
|
Joined: Aug 2012
Posts: 166
Contributor
|
Contributor
Joined: Aug 2012
Posts: 166 |
If you want Ac try these brackets
|
|
|
|
Joined: Aug 2011
Posts: 11
Active BB Member
|
OP
Active BB Member
Joined: Aug 2011
Posts: 11 |
Eh AC is too much or a pain to install, plus I never use it in Colorado
|
|
|
|
Joined: Oct 2007
Posts: 411
Contributor
|
Contributor
Joined: Oct 2007
Posts: 411 |
ITS EASY TO MAKE THESE BRACKETS IF YOU HAVE A ENGINE ON A STAND WHERE YOU CAN GET TO IT EASY. THAT CLIFFORD ALUM TIMMING COVER IS NEAT. NEVER SEEN ONE OF THEM BEFORE. WHERE DID YOU GET IT STANZ BOB
I BELIEVE IN " JOHN 3:16 "
|
|
|
|
Joined: Aug 2012
Posts: 166
Contributor
|
Contributor
Joined: Aug 2012
Posts: 166 |
ITS EASY TO MAKE THESE BRACKETS IF YOU HAVE A ENGINE ON A STAND WHERE YOU CAN GET TO IT EASY. THAT CLIFFORD ALUM TIMMING COVER IS NEAT. NEVER SEEN ONE OF THEM BEFORE. WHERE DID YOU GET IT STANZ BOB That's not my motor, its just a pic i found surfin the net. I think Clifford stopped making those covers since I don't see them listed on their site. I have heard they might start making them again. lets hope so, I want one!
|
|
|
0 members (),
125
guests, and
27
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
|
|
|