Maikng it more difficult than it needs to be.

12 Port News - Features

12 Port History

Casting Numbers

Online Store

Tech Tips

Become a Member

Print Thread

Rate Thread

Re: Maikng it more difficult than it needs to be. straight axle 63 #81347 07/04/14 02:18 PM
Joined: Sep 2004 Posts: 5,839 Likes: 1 Ca M Mean buzzen half dozen A.K.A. Hank OP 1000 Post Club
OP Mean buzzen half dozen A.K.A. Hank 1000 Post Club M Joined: Sep 2004 Posts: 5,839 Likes: 1 Ca	Yeah, I do not know where he gets his info from but wherever he did, he needs to get better informed.. Yes, you would leave the boss in for what he was looking for. Removing the boss just made him lose port velocity & low RPM power, just what he says he was looking to gain, more power down low. He does not put in lumps, he says lumps are for high RPM power, that is why he did not want to put them in, he is not racing or want higher RPM power, hence he removed the boss he put 8 videos on YouTube . I would not recommend to use any advise from the vids, for the most part. MBHD 12 port SDS EFI

Entire Thread
Subject	Posted By	Posted
Maikng it more difficult than it needs to be.	Mean buzzen half dozen A.K.A. Hank	07/03/14 07:04 PM
Re: Maikng it more difficult than it needs to be.	CNC-Dude #5585	07/03/14 08:40 PM
Re: Maikng it more difficult than it needs to be.	Twisted6	07/04/14 12:24 PM
Re: Maikng it more difficult than it needs to be.	straight axle 63	07/04/14 01:15 PM
Re: Maikng it more difficult than it needs to be.	Mean buzzen half dozen A.K.A. Hank	07/04/14 02:18 PM
Re: Maikng it more difficult than it needs to be.	Beater of the Pack	07/04/14 11:13 PM
Re: Maikng it more difficult than it needs to be.	Lifeguard	07/04/14 11:21 PM
Re: Maikng it more difficult than it needs to be.	Mean buzzen half dozen A.K.A. Hank	07/05/14 02:18 AM
Re: Maikng it more difficult than it needs to be.	Twisted6	07/05/14 08:40 AM
Re: Maikng it more difficult than it needs to be.	Lifeguard	07/05/14 09:23 AM
Re: Maikng it more difficult than it needs to be.	DeuceCoupe	07/05/14 01:49 PM
Re: Maikng it more difficult than it needs to be.	CNC-Dude #5585	07/05/14 09:16 PM
Re: Maikng it more difficult than it needs to be.	Lifeguard	07/05/14 09:37 PM
Re: Maikng it more difficult than it needs to be.	Mean buzzen half dozen A.K.A. Hank	07/06/14 03:32 AM
Re: Maikng it more difficult than it needs to be.	CNC-Dude #5585	07/06/14 03:44 AM
Re: Maikng it more difficult than it needs to be.	tlowe #1716	07/06/14 04:08 PM
Re: Maikng it more difficult than it needs to be.	Mean buzzen half dozen A.K.A. Hank	07/06/14 04:28 PM
Re: Maikng it more difficult than it needs to be.	Lifeguard	07/06/14 05:20 PM
Re: Maikng it more difficult than it needs to be.	tlowe #1716	07/06/14 06:04 PM
Re: Maikng it more difficult than it needs to be.	Mean buzzen half dozen A.K.A. Hank	07/07/14 01:14 PM
Re: Maikng it more difficult than it needs to be.	CNC-Dude #5585	07/07/14 01:34 PM
Re: Maikng it more difficult than it needs to be.	Mean buzzen half dozen A.K.A. Hank	07/07/14 03:17 PM

Moderated by stock49, Twisted6, will6er

Link Copied to Clipboard

Inliners International Forums General Discussion Hi Performance Maikng it more difficult than it needs to be.