292 with Offy 3x1 = .080 Jets Still Too Lean??

12 Port News - Features

12 Port History

Casting Numbers

Online Store

Tech Tips

Become a Member

Print Thread

Rate Thread

Re: 292 with Offy 3x1 = .080 Jets Still Too Lean?? Countn'Carbs #92109 06/28/17 08:41 PM
Joined: Jul 2000 Posts: 4,586 Likes: 20 Palatka FL. USA Twisted6 1000 Post Club
Twisted6 1000 Post Club Joined: Jul 2000 Posts: 4,586 Likes: 20 Palatka FL. USA	You may not have enough fuel Pressure Or Vol. to keep the carb Bowls full. Try and take the linkage off one carb and Test drive to see if it will now go over the 4k issue If so That is your issue not enough fuel to the carbs. Larry/Twisted6 [oooooo] Adding CFM adds boost God doesn't like ugly.

Entire Thread
Subject	Posted By	Posted
292 with Offy 3x1 = .080 Jets Still Too Lean??	Countn'Carbs	06/28/17 04:53 PM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	Twisted6	06/28/17 08:41 PM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	Countn'Carbs	06/28/17 09:14 PM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	CNC-Dude #5585	06/28/17 10:47 PM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	Countn'Carbs	06/28/17 11:01 PM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	Twisted6	06/29/17 08:52 PM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	efi-diy	06/28/17 11:23 PM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	tlowe #1716	06/29/17 12:23 AM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	Countn'Carbs	06/29/17 12:44 AM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	efi-diy	06/29/17 02:07 AM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	mdonohue05	06/29/17 07:05 PM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	Countn'Carbs	06/30/17 12:44 AM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	Countn'Carbs	06/29/17 10:47 PM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	Countn'Carbs	06/29/17 11:10 PM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	THE FRENCHTOWN FLYER	06/29/17 11:13 PM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	Countn'Carbs	06/29/17 11:30 PM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	mdonohue05	06/30/17 12:45 AM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	CNC-Dude #5585	06/30/17 10:19 AM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	Countn'Carbs	06/30/17 11:41 AM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	Countn'Carbs	06/30/17 11:35 AM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	mdonohue05	06/30/17 03:19 PM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	efi-diy	07/01/17 02:24 PM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	preacher-no choir	07/01/17 07:52 PM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	Countn'Carbs	07/02/17 01:23 AM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	Countn'Carbs	07/02/17 01:05 AM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	preacher-no choir	07/01/17 08:12 PM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	Countn'Carbs	07/02/17 01:29 AM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	Countn'Carbs	07/02/17 01:34 AM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	Countn'Carbs	07/10/17 11:46 AM

Moderated by stock49, Twisted6, will6er

Link Copied to Clipboard

Inliners International Forums General Discussion Hi Performance 292 with Offy 3x1 = .080 Jets Still Too Lean??