292 with Offy 3x1 = .080 Jets Still Too Lean??

12 Port News - Features

12 Port History

Casting Numbers

Online Store

Tech Tips

Become a Member

Print Thread

Rate Thread

Re: 292 with Offy 3x1 = .080 Jets Still Too Lean?? mdonohue05 #92133 06/30/17 10:19 AM
Joined: Sep 2008 Posts: 3,669 Likes: 42 N. Georgia CNC-Dude #5585 1000 Post Club
CNC-Dude #5585 1000 Post Club Joined: Sep 2008 Posts: 3,669 Likes: 42 N. Georgia	Can you verify the float levels are at their correct height, if they are too low or inconsistent on all 3 carbs, it can starve the engine for fuel as well. Class III CNC Machinist/Programmer

Entire Thread
Subject	Posted By	Posted
292 with Offy 3x1 = .080 Jets Still Too Lean??	Countn'Carbs	06/28/17 04:53 PM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	Twisted6	06/28/17 08:41 PM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	Countn'Carbs	06/28/17 09:14 PM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	CNC-Dude #5585	06/28/17 10:47 PM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	Countn'Carbs	06/28/17 11:01 PM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	Twisted6	06/29/17 08:52 PM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	efi-diy	06/28/17 11:23 PM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	tlowe #1716	06/29/17 12:23 AM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	Countn'Carbs	06/29/17 12:44 AM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	efi-diy	06/29/17 02:07 AM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	mdonohue05	06/29/17 07:05 PM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	Countn'Carbs	06/30/17 12:44 AM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	Countn'Carbs	06/29/17 10:47 PM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	Countn'Carbs	06/29/17 11:10 PM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	THE FRENCHTOWN FLYER	06/29/17 11:13 PM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	Countn'Carbs	06/29/17 11:30 PM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	mdonohue05	06/30/17 12:45 AM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	CNC-Dude #5585	06/30/17 10:19 AM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	Countn'Carbs	06/30/17 11:41 AM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	Countn'Carbs	06/30/17 11:35 AM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	mdonohue05	06/30/17 03:19 PM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	efi-diy	07/01/17 02:24 PM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	preacher-no choir	07/01/17 07:52 PM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	Countn'Carbs	07/02/17 01:23 AM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	Countn'Carbs	07/02/17 01:05 AM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	preacher-no choir	07/01/17 08:12 PM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	Countn'Carbs	07/02/17 01:29 AM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	Countn'Carbs	07/02/17 01:34 AM
Re: 292 with Offy 3x1 = .080 Jets Still Too Lean??	Countn'Carbs	07/10/17 11:46 AM

Moderated by stock49, Twisted6, will6er

Link Copied to Clipboard

Inliners International Forums General Discussion Hi Performance 292 with Offy 3x1 = .080 Jets Still Too Lean??