|
Joined: Jul 2004
Posts: 365
Contributor
|
OP
Contributor
Joined: Jul 2004
Posts: 365 |
I have a set of 6 Hudson connecting rods. They have a bushed wrist pin of .968 diameter, are 8.125 inches center to center, with a big end of 2 1/8 inch. $150.00.
|
|
|
|
Joined: Aug 2007
Posts: 473 Likes: 1
Contributor
|
Contributor
Joined: Aug 2007
Posts: 473 Likes: 1 |
Armond Which motor are they from and do you have anything for a 308 you might want to part with? Have another Inliners member looking for parts. Thanks Rich,
Last edited by nln6pinto; 05/27/18 04:05 PM.
Az Chapter Head
34' Ford Cabriolet Ford 300 & C-4 under Construction
|
|
|
|
Joined: Jul 2004
Posts: 365
Contributor
|
OP
Contributor
Joined: Jul 2004
Posts: 365 |
These are all I have. I honestly don't know which engine they are out of. How do you tell the difference and I will check. PN casting?
|
|
|
|
Joined: Jan 2005
Posts: 2,123 Likes: 3
1000 Post Club
|
1000 Post Club
Joined: Jan 2005
Posts: 2,123 Likes: 3 |
IIRC all 232, 262, 308 rods are 8.125" long, 2.125" big end, but not sure if the same. The block and MB lengths match, so it's possible.
|
|
|
|
Joined: Jul 2004
Posts: 365
Contributor
|
OP
Contributor
Joined: Jul 2004
Posts: 365 |
and they are all drop forged steel. I do know the engine they came out of had an approximate bore of 3.75 inch (with a ruler) but that's all of the information the fellow had. I'm guessing it was closer to 3.8 and it was a 308 but there is no way to know for sure without a casting number.
Last edited by Armond, II#298; 05/28/18 09:04 AM.
|
|
|
|
Joined: Aug 2007
Posts: 473 Likes: 1
Contributor
|
Contributor
Joined: Aug 2007
Posts: 473 Likes: 1 |
Az Chapter Head
34' Ford Cabriolet Ford 300 & C-4 under Construction
|
|
|
|
Joined: Oct 2007
Posts: 5,041 Likes: 51
1000 Post Club
|
1000 Post Club
Joined: Oct 2007
Posts: 5,041 Likes: 51 |
I have two sets of rods and pistons that were said to be 308 when I bought them on eBay. They measure out the same as above. One set of pistons measures 3.80" and is a long heave piston with 4 rings. One on the skirt. The rods have # 5303906 The other set has pistons that measure 3.85" and are lighter and shorter. They have 3 rings. The number on them is 303906 a diamond 24. They all have bearings in them that measure about 2.1".
"I wonder if God created man because he was disappointed in the monkey?" Mark Twain
|
|
|
|
Joined: Jul 2004
Posts: 365
Contributor
|
OP
Contributor
Joined: Jul 2004
Posts: 365 |
5 of these rods are marked 303906 diamond 19 and one is just 303906. They all look identical. Thank you
Last edited by Armond, II#298; 05/28/18 07:50 PM.
|
|
|
|
Joined: Oct 2007
Posts: 5,041 Likes: 51
1000 Post Club
|
1000 Post Club
Joined: Oct 2007
Posts: 5,041 Likes: 51 |
Welcome! Hope they find a good home.
"I wonder if God created man because he was disappointed in the monkey?" Mark Twain
|
|
|
|
Joined: Jul 2004
Posts: 365
Contributor
|
OP
Contributor
Joined: Jul 2004
Posts: 365 |
Me too!
|
|
|
|
Joined: Jul 2004
Posts: 365
Contributor
|
OP
Contributor
Joined: Jul 2004
Posts: 365 |
|
|
|
0 members (),
125
guests, and
27
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
|
|