|
|
Joined: Aug 2004
Posts: 26
Active BB Member
|
OP
Active BB Member
Joined: Aug 2004
Posts: 26 |
I have a stock 65 292 and would like to know if these little 'Pinto' carbs flow enough for my engine...I can deal with the jetting ok. This is in a C10 with HEI and 700R4. I dont expect to carry much weight, just looking for gas mileage.. any suggestions appreciated.
"Keep it simple ------!"
|
|
|
|
Joined: Sep 2001
Posts: 510
Major Contributor
|
Major Contributor
Joined: Sep 2001
Posts: 510 |
According to Tom Langdon, Holley Webers out of the box are good for about 200 cfm. My experience so far with two of them on a 320 cid GMC appears to confirm that. At 4,000 rpm your 292 will need 338 cfm. Two of them should work well for you; one is not enough, unless you are proceeding slowly by design.
God's Peace to you.
d
|
|
|
|
Joined: Sep 2000
Posts: 588
Major Contributor
|
Major Contributor
Joined: Sep 2000
Posts: 588 |
Tom, I have installed one of these carbs on my '65 Pickup with a stock 292 also. It has HEI, headers and an aluminum intake. I am not driving the truck as of yet (still finishing up body work) but I can tell you that after I installed it, it fired right up and idles and accelerates with no problem when it is sitting there. I was very impressed with the first fireup but I am afraid I can't give you any driveability performance on it yet.
Ontario Inliners 1965 Chevelle 1940 Chev 1965 Chev Pick-up 1970 MGB Roadster
|
|
|
|
Joined: Oct 2004
Posts: 81
Active BB Member
|
Active BB Member
Joined: Oct 2004
Posts: 81 |
Tom - the Holley/Weber 5200 is just slightly larger than the stock carb for your 292. You may want to play with jetting a bit after you get your truck on the road. It's cheap and easy. Go to the Weber Direct web site, and you'll find whatever you need.
Boo
Paint it black with a rattle can, and drive it like ya stole it!
|
|
|
|
Joined: Mar 2004
Posts: 565
Major Contributor
|
Major Contributor
Joined: Mar 2004
Posts: 565 |
Tom, My experiance says it should work just fine. You'll need a one barrel-to-two barrel adapter that Tom Langdon sells for a simple bolt on experiance. You should pull the jets out to see if they are the right size and in the correct position. Sometimes in the rebuilding process, they get switched. The small jet naturally goes in the primary. I use 51's in the primary and 54's in the secondary. I have 3-HW on my warmed over 292. They run a bit rich but it purrs like a kitten when you open them up! Heck, I didn't spend all of this money to save on gas. Be sure to go with an HEI or Pertronics upgrade. They help quite a lot on starting. They look way cool too! RapRap 1940 ChoppedChevyCoupe
Loud Pipes Saves Lives!
|
|
|
|
Joined: Aug 2004
Posts: 26
Active BB Member
|
OP
Active BB Member
Joined: Aug 2004
Posts: 26 |
Thanks to all for the replies.I'm in the middle of a rejuvinate on my truck and have been collecting pieces for about 18 months.Since I'm going to have to come up with a linkage for the trans, I only want do do this once.For an adapter you would recommend???
"Keep it simple ------!"
|
|
|
|
Joined: Sep 2000
Posts: 588
Major Contributor
|
Major Contributor
Joined: Sep 2000
Posts: 588 |
If you are putting a 700R4 on your 292 you won't need an adaptor Tom. It will bolt right up. Now the trans mount is a different story. Try and find an automatic crossmember from a 63-66 truck and you should be able to adapt that to the 700R4.
Ontario Inliners 1965 Chevelle 1940 Chev 1965 Chev Pick-up 1970 MGB Roadster
|
|
|
|
Joined: Aug 2004
Posts: 26
Active BB Member
|
OP
Active BB Member
Joined: Aug 2004
Posts: 26 |
GM Dad, thanks again for the reply. I'm all set with the trans. except for the tv cable set-up. I was able flip the e-brake crossmember and gusset it off the top frame rail. The e-brake is also set up using 99% original parts. I would really like to keep the truck as original looking as reasonably possible, but I need fuel mileage too for regular trips to Calgary (75 mi.one way)I didnt realise how simple it is to swap steering columns. I swapped my original shaft into a 76 van auto assembly and used my original wheel.Looks original enough to me.Anyhow,sorry for rambling,getting excited over whats finally starting to happen in the shop. Tom.
"Keep it simple ------!"
|
|
|
1 members (stock49),
260
guests, and
27
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
|
|
|