|
Joined: Jul 2005
Posts: 5
Active BB Member
|
OP
Active BB Member
Joined: Jul 2005
Posts: 5 |
Do I need a ballast resistor for the coil and do I have to do any thing with the gas gauge and amp gauge ???
|
|
|
|
Joined: Dec 2000
Posts: 3,332
1000 Post Club
|
1000 Post Club
Joined: Dec 2000
Posts: 3,332 |
Yes to both questions. Patrick's has that in stock. But the amp guage stays stock Good luck.
John M., I.I. #3370
"There are no shortcuts to any place worth going". -Anon
|
|
|
|
Joined: Mar 2001
Posts: 272
Contributor
|
Contributor
Joined: Mar 2001
Posts: 272 |
Be sure the amp meter is compatible with the alt. or gen. you use.
Sam II2935
'38 Stude/292
|
|
|
|
Joined: Mar 2001
Posts: 272
Contributor
|
Contributor
Joined: Mar 2001
Posts: 272 |
By that I meant will carry the current.
'38 Stude/292
|
|
|
|
Joined: Aug 2003
Posts: 1,905
1000 Post Club
|
1000 Post Club
Joined: Aug 2003
Posts: 1,905 |
Jumping in on your question 4door52: Would I need a step down for the stock heater blower motor in my '50 3100? This may have been answered here before, but I can't find it.
Drew Mid-Atlantic Chapter
|
|
|
|
Joined: Aug 2003
Posts: 1,905
1000 Post Club
|
1000 Post Club
Joined: Aug 2003
Posts: 1,905 |
Thanks Walt, I am rewiring completely as the original wires are very frayed even though all the systems work except for one parking lamp. A local starter rebuild shop may be able to help me on the heater motor.I've already disconnected and removed everything from under the dashboard so the rest should be easy.LOL
Drew Mid-Atlantic Chapter
|
|
|
|
Joined: Aug 2003
Posts: 1,905
1000 Post Club
|
1000 Post Club
Joined: Aug 2003
Posts: 1,905 |
Wiring it myself? Good one Walt.I'm new to this stuff so it's a kit from American Auto Wire,the Factory Fit people. I am very fortunate to live about 15 minutes by highway from their plant, so I just drove over, told them what I was doing, plopped down some $$ and wa-la, a kit for my 3100. And I didn't have to buy their expensive overloaded kit either because I'm not planning on adding a bunch of modern stuff. They're were very helpful and have a great tech group to rely on so I think I'll be ok on this project. And I have noted your advice too. Thanks.
Drew Mid-Atlantic Chapter
|
|
|
|
Joined: Dec 2000
Posts: 3,332
1000 Post Club
|
1000 Post Club
Joined: Dec 2000
Posts: 3,332 |
Dear Drew; Patrick's has the wiring diagrams & done many of these. Give them a call for more info. Good luck.
John M., I.I. #3370
"There are no shortcuts to any place worth going". -Anon
|
|
|
|
Joined: Jan 2006
Posts: 2
Newcomer
|
Newcomer
Joined: Jan 2006
Posts: 2 |
go to speedwaymotors.com and look for their 6 to 12 volt conversion guide. its cheap, and has everything you need to know.
|
|
|
|
Joined: Feb 2005
Posts: 122
Contributor
|
Contributor
Joined: Feb 2005
Posts: 122 |
Does anybody have a "kit" for 12 volt conversion? I'm going to be picking up a '49 4 door myself here soon and would like to upgrade. It would just make life easier if a kit was supplied with all the necessary bulbs, switches, drop downs, etc.
Thx. Butch
Butch W. '49 Chevy Sedan (stock) '55 Buick Special '65 Rambler Classic
|
|
|
|
Joined: Dec 2000
Posts: 3,332
1000 Post Club
|
1000 Post Club
Joined: Dec 2000
Posts: 3,332 |
Dear Butch; It will be cheaper for you to buy, just what's needed. Patrick's catalog has the list. You can call me for help as I have done dozens over the years. Good luck.
John M., I.I. #3370
"There are no shortcuts to any place worth going". -Anon
|
|
|
0 members (),
298
guests, and
33
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
|
|