|
|
|
|
Joined: Nov 2005
Posts: 12
Active BB Member
|
OP
Active BB Member
Joined: Nov 2005
Posts: 12 |
Hi guys
I would like to hook up a 700 R Transmission to my 292, does anyone know what size of flex plate and matching starter is needed for this project....Thanks
|
|
|
|
|
Joined: Oct 2007
Posts: 5,015 Likes: 47
1000 Post Club
|
|
1000 Post Club
Joined: Oct 2007
Posts: 5,015 Likes: 47 |
... and how to hook up and adjust the throttle cable.
"I wonder if God created man because he was disappointed in the monkey?" Mark Twain
|
|
|
|
|
Joined: Mar 2001
Posts: 272
Contributor
|
|
Contributor
Joined: Mar 2001
Posts: 272 |
Phoenix trans in TX sells a neat adapter for the carb linkage for proper hookup of the T V cable. Makes it easy to do. Probably not available for just any carb but I got one for my Edelbrock. Worth a call to find out.
'38 Stude/292
|
|
|
|
|
Joined: May 2000
Posts: 680
Major Contributor
|
|
Major Contributor
Joined: May 2000
Posts: 680 |
You can use either a 153 or 168 tooth early style 265-350 small block flexplate Depending on your crankshaft, you may need to drill the holes out to 1/2" and/or add two additional dowel holes. I do not remember the converter pattern, but if you get an aftermarket flex plate with the dual pattern convertor holes you will be fine.
Bow-Tie Overdrives has an easy to use set up for the TV cable (TV-EZ??) but I believe they only have them for 4 barrels.
Inliner #1916
|
|
|
|
|
Joined: Aug 2004
Posts: 26
Active BB Member
|
|
Active BB Member
Joined: Aug 2004
Posts: 26 |
Hey fellow Canuck! I did the same thing to my 65 C10 292...700R4 from a 92 305 truck. The starter and flexplate bolted on direct.I think I used new flexplate bolts from the dealer. The linkage for the tv cable was another story! It MUST work smoothly and travel very close to the specified distance between idle and wide open throttle. I am using the original carb and a homemade linkage given to me on an old intake from EFI-DIY (this site or Chevy-Talk) in Calgary. When the weather clears I can take a better look at mine to give you a decent description. At this point my shift points are a little high, but close enough to drive from Calgary to N.S. with a full load on board. Tom
"Keep it simple ------!"
|
|
|
|
|
Joined: Oct 2007
Posts: 5,015 Likes: 47
1000 Post Club
|
|
1000 Post Club
Joined: Oct 2007
Posts: 5,015 Likes: 47 |
So, If I'm using the 700R4 and the TBI from the same '89 305 donor truck I can use the flex plate. torque converter, starter. and TV cable with an extension? Tom
"I wonder if God created man because he was disappointed in the monkey?" Mark Twain
|
|
|
|
|
Joined: Apr 2004
Posts: 3,556 Likes: 35
1000 Post Club
|
|
1000 Post Club
Joined: Apr 2004
Posts: 3,556 Likes: 35 |
Beater and guy's,
The flex plate will not fit from any SBC with a newer design 1 piece rear seal. It will have to be from a 85 or older V8.
I have used the 168 tooth ring gear on multiple applications. Use a starter from later model engine , such as a 99' with a 350. They had a small high tq starter. lots of clearance with them. Tom
Inliner Member 1716 65 Chevelle Wagon and 41 Hudson Pickup Information and parts www.12bolt.com
|
|
|
|
|
Joined: Oct 2007
Posts: 5,015 Likes: 47
1000 Post Club
|
|
1000 Post Club
Joined: Oct 2007
Posts: 5,015 Likes: 47 |
Will the 700R4 Converter bolt to the flex plates used on a 292?
"I wonder if God created man because he was disappointed in the monkey?" Mark Twain
|
|
|
|
|
Joined: Apr 2004
Posts: 3,556 Likes: 35
1000 Post Club
|
|
1000 Post Club
Joined: Apr 2004
Posts: 3,556 Likes: 35 |
Inliner Member 1716 65 Chevelle Wagon and 41 Hudson Pickup Information and parts www.12bolt.com
|
|
|
|
|
Joined: Oct 2007
Posts: 5,015 Likes: 47
1000 Post Club
|
|
1000 Post Club
Joined: Oct 2007
Posts: 5,015 Likes: 47 |
"I wonder if God created man because he was disappointed in the monkey?" Mark Twain
|
|
|
|
1 members (stock49),
161
guests, and
42
robots. |
|
Key:
Admin,
Global Mod,
Mod
|
|
|
|
|
|
