Inliners International Forums General Discussion Bench racing Class records

Can someone post some of the class records from the inliners????

If you join Inliners International pages of Drag and Land speed Records appear in every issue of 12 Port News. It's a 3 page list and would be time consuming to type in. Are you interested in a specific class?

Scott, your car would likely fall into the CA/S class, which is an Altered Coupe class with an 8 lbs/ci minimum engine rule. Thats one of the classes my Camaro is going to fit into as well. The records for that class are 11.72 ET, and 112.24 MPH in the quarter. The Gas Coupe class could also be an option, but has a heavier 10.1 lbs/ci minimum weight. My Camaro is also going to fit that class with a smaller engine. The class for your car would be CG/S, and the record for it is 11.72 ET also, with no MPH record listed for that class. The rules for all the classes are listed to the far left column of this page in the "Racing" section. Hope this helps.

The current Inliners drag racing rules are posted under the 'Racing' link in the main menu.

Tim

Thanks guys!!!!

My car is a 65 Comet 2800# with me in it... The engine is a Destroked 300 (272ci) it has gone 10.96@120mph with side-draft Webers/ 11.14@118 with a single 4 barrel..

SCOTT:
What sizes engine are you going to run in your Camaro????

I will run a 250+.060 in the Gas Coupe class, and a 292+.060 in the Altered Coupe class, that way my car weight will stay at around 2600 lbs for either class. It'll just be a little heavy for the minimum weight in the Altered Coupe class.

2600# is that with you in it???

I'm trying to take some weight off my car... Thinking of a cast crank (stroked 240) -20#, lite weight seat, chome-moly lower control arms/strut rods, lexan windsheld, and some hole sawing and mybe lossing some weight myself HA HA HA!!!

Yeah, it weighed 3100# with a concrete filled Big Block in it with the driver and still ran 8.20's in the quarter. So I hope the 6 cylinder will lighten it up a bunch. It still has the stock seats and carpet in it, and the stock front K member also. I can pull a good 300# out of it pretty easy, plus what ever the difference in engine weight is in comparison. The previous owner weighed 200#, and so do I, so that much will be the same. Im putting a 5 speed in it also that will be a little lighter than the automatic he was running. Then I will look at some forced induction classes and move into that.

OK, since SIXGUN, & CnC-Dude are askin questions. Where would my pinto fall into class wise? production headed 300, tube chassis, should be in the 2100 lb area on gas.

Rich, you could be in the "B" classes of both Gas Coupe and Altered Coupe. The Gas Coupe "B" class is 7.6 lbs/ci, and the Altered Gas "B" class is 6 lbs/ci.

RICH:
If we could put my engine in your car WOW THAT THING WOULD FLY !!!!! At least 9.90s now that would be cool ...

How much weight do you think you can get rid of in your Comet.

Not real sure??? Shooting for 150/200#... Already have lexan back and side windows, fiberglass hood,fenders,bumpers,trunk lid, light weight wheels, brakes, center sec, chome-moly cage...

Are your doors still pretty heavy.

NO guted and hole sawed the bottoms, the hinges are thick mybe thin them out or make out of alum...

Its hard to imagine your car being that heavy.

Well I'm a big boy 250#, the car it self is 2550#

Well if you could lose 150-200# off the car, that would be good. Im lucky, a lot of my body panels are plastic.

I'm going to try to lose 50# my self...

Good luck with that, its difficult sometimes to do.

I used to work for a guy who was known to build, by far, the lightest helicopters of a given type. I once asked him the secret to getting them so much lighter than others did. He said the thing was that EVERYTHING counts. Most people look for the big savings, but he said don't forget the small things, which add up if you can find enough of them. Even a 1/2 pound savings times many units will become significant.

I used to work for a guy who was known to build, by far, the lightest helicopters of a given type. I once asked him the secret to getting them so much lighter than others did. He said the thing was that EVERYTHING counts. Most people look for the big savings, but he said don't forget the small things, which add up if you can find enough of them. Even a 1/2 pound savings times many units will become significant.

Bob Glidden when he was running Super Stock said every ounce counts and used to take the change out his pockets, remove the guts out of the stock guages, every other spring out of the rear seat and add weight where he needed it.

Jalopy, are you going to have your dragster ready for any of these Inline races this season.

I'm trying to get the time, biggest problem is getting a new trailer, selling my 18 wheeler at he end of the month (semi retiring) so won't be able to use my 53 footer anymore.

Check out HemiRambler's tilting, air-actuated, open trailer over on the HAMB. He hauls his FED with it and refused to go enclosed

Semi retiring.

I don't know if it was intentional, but good pun.

Several of the bucks up guys at Bonneville use a trailer that kneels with air bag suspension (deflate the bags and the trailer squats) to transport the race cars around the salt (for any that don't know it's actually against the rules to drive a competition vehicle, under it's own power, anywhere but on one of the courses, so towing or pushing are the methods used to get them to and from the courses).

The tech wouldn't be that difficult to copy for someone of lesser finacial means than George Poteet, and should be very easy on the car while going down the road.

I would design in some removeable bump stops though, as I wouldn't want the trailer to loose an air line and squat going down the interstate.

Dose anyone have pic's of the cars/engines in any of the classes

Ron's truck is in the Gas Coupe class. Im sure you've seen those pics. The pics for the Altered Coupe record holder were in the issue before last 12 Port News, its a 50's Chevy with a 292. Maybe someone has pics of it they could post.

Is it this one?

http://www.youtube.com/watch?v=isq9LZyPgzU

MBHD

Yeah, thats it. He has the record in the aluminum head class with a Sissell 12 Port head. It's a 11.40@116.86 MPH in the Alterd Coupe class. Pretty fast for a 3000 Lb truck.

Ya RONS truck is going to F/N fly when he gets it dialed-in (I have to watch-out for him)....

Maybe CI will have their new aluminum head ready before long and you could try it out. That should help you drop some weight off the front end a little too.

That would be nice!!!

Are you going to try one of those SISSEL heads on anything??? That would make one hell of a WING-ZINGER engine (250ci at 10,000 RPM)

I will need to switch to an aluminum head for the supercharged class I am going to get into later on, its the CCA/A class in Altered Coupe. Depends on how light I can get the car. With a 258 it can weigh 2062, and with a 301 it can weigh 2408. As soon as I can get my tranny, I will start mocking up for headers, oil pan and engine plate.

Sounds like I need to watch-out for you now!!!!

Do you think it's going to take you a long time to get the car together??? You just need engine/trans??? What rear gear are you planning on (I run a 5:43 in my car)????

Yeah, just engine and tranny is all I need. My rear end has a 4.56 in it now. I'll try it out to see how it works with the tranny I get before I decide on changing it. Keep in mind im shooting for 2600 with me in the car, so I wont need to have a real low gear.

Hope to have my other 65 Elco out for some runs this summer too. It is going into the shop real soon to piece it together.

This might be a fun summer for the inline folks.

Won't know the weight till it's further together.

That sounds good Tom, looks like there will be a lot of Inliner racing going on this year. Hopefully some new records will be set. Thats my intention with all the different classes I am going to be putting my car into(LOL). Maybe we will have some fun too :D.