250 Turbo I6 - Inliners International Bulletin Board

You are not logged in. [Log In] Inliners International » Forums » General Discussion » Blown and Injected » 250 Turbo I6

Page 3 of 3

3

Topic Options

Rate This Topic

#69286 - 04/01/12 04:15 PM Re: 250 Turbo I6 [Re: turbo nova]
Mean buzzen half dozen A.K.A. Hank Mean buzzen half dozen A.K.A. Hank Active BB Member Registered: 09/23/04 Posts: 4550 Loc: Ca	Very nice looking! Just something to think abou for the exhaust downpipe, normally, you would want nice gentle bends, (like mandrel bent tubing) no sharp edges & have the tubing as big as possible. Mine is not the greatest, I made the joggle to clear the steering box, it is smoother on the inside than the outside. MBHD _________________________ 12 port SDS EFI
Top

#69287 - 04/01/12 05:05 PM Re: 250 Turbo I6 [Re: Mean buzzen half dozen A.K.A. Hank]
tlowe #1716 tlowe #1716 12 PORT ADVERTISER Active BB Member Registered: 04/01/04 Posts: 2333 Loc: Dysart, Iowa	Wow, need to get my sunglasses out to look at it! One problem I see, the oil drain line on turbo should not have the lower hanging section. It hangs lower than the conection to the pan. The oil when leaving the turbo is all frothed up and needs the easiest route possible to flow. Keep up the good work! Tom _________________________ 12 PORT ADVERTISER http://www.inliners.org/Advertisers/index.html trbo writeup http://www.inliners.org/ubbthreads/ubbthreads.php?ubb=showflat&Number=43253&fpart=1
Top

#69288 - 04/01/12 05:07 PM Re: 250 Turbo I6 [Re: tlowe #1716]
turbo nova turbo nova Active BB Member Registered: 07/06/09 Posts: 48 Loc: louisiana	yes i realized that as well, i need a elbow and a shorter line and that will do the trick.
Top

#69293 - 04/02/12 09:20 PM Re: 250 Turbo I6 [Re: turbo nova]
McGoo McGoo Active BB Member Registered: 09/24/05 Posts: 69 Loc: Airdrie, Alberta	Wow that looks great! Lots of ideas there for my little project. Paul _________________________ V8 camaros are like navels,...everybody has one. EFI Turbo 250 project well under way.
Top

#70630 - 07/05/12 12:03 PM Re: 250 Turbo I6 [Re: McGoo]
turbo nova turbo nova Active BB Member Registered: 07/06/09 Posts: 48 Loc: louisiana	Finished fiting the front together and put her back on the ground Also Threw the engine in today to check fitment, for the most part everything fit, its back to the drawing board with exhaust but ill figure it out. Uploaded with ImageShack.us Uploaded with ImageShack.us Uploaded with ImageShack.us Uploaded with ImageShack.us Uploaded with ImageShack.us Uploaded with ImageShack.us Uploaded with ImageShack.us Uploaded with ImageShack.us
Top

#70631 - 07/05/12 05:26 PM Re: 250 Turbo I6 [Re: turbo nova]
Mean buzzen half dozen A.K.A. Hank Mean buzzen half dozen A.K.A. Hank Active BB Member Registered: 09/23/04 Posts: 4550 Loc: Ca	Looking great! Why back to the drawing board on the exhaust? What happened? If you do not mind. MBHD _________________________ 12 port SDS EFI
Top

#73147 - 12/23/12 04:43 PM Re: 250 Turbo I6 [Re: Mean buzzen half dozen A.K.A. Hank]
Toolmaker Toolmaker Bulletin Board Only Member Registered: 12/30/10 Posts: 2 Loc: SWEDEN	Hi Have followed your project with big intrest from the start. Looking realy good! Have you done som progress? Looking forward to updates!
Top

Page 3 of 3

3

Previous Topic

Previous Topic View All Topics

View All Topics

Index Next Topic

Next Topic

Moderator: Webmaster

Hop to:

Who's Online

8 registered (wdschell, HiTork, radar, Mean buzzen half dozen A.K.A. Hank, mdonohue05, panic) and 58 anonymous users online.

Newest Members

II Much Roof, William Allen, Masi Isohanni, Chris at BHJ, 66van292
5483 Registered Users

Generated in 1.633 seconds in which 1.586 seconds were spent on a total of 16 queries. Zlib compression unavailable.